Have been itchy to try digi camo on Zoids for some time...
Preparing the lightest color first....then mask it with modeling tape. I peeled on/away the tape a few time to reduce the "sticky-ness" to prevent it from sucking up the paint :D Adding the secondary color and mask it again...Finally adding the darkest color and peel off all the tapes... O_o)"
First off... Shopping~! I need to get the ingredient for this creation...and after a couple of explaining myself to the store owner... i finally hit the jackpot at the local artfriend... The critical dome for the cockpit turned out to be a Xmas deco ball... :D And the arms are jewellery metallic beads purchased when my wife went to get her accessories whatsnot...
Next, the silhouette filling...(In order to protect the surface of the Xmas ball, I mummified it X_X) And the cockpit control panel... Deathsaurer's parts are modified to become the "hood" of the squid.
With the Singaporean designer seat Adding it all together Yes, the cushion are actually broken plastic spoons. http://www.blogger.com/img/blank.gif Seeing how transparent the dome can be, the back wall must be well-detailed as well...again, plastic spoons to the rescue :D This is a tough act as the padded wall must conform to the dome shape...Blue-tac is your best friend here ;) Once the positioning is achieve, super glue and putty is generously applied :D Seen next to the padded dome on the previous picture are the dumpling for this Duanwu Festival hehee... they are actually casting mold for the tentacles. And here's the tentacles
Next is the mantle which is the main body of the squid... Recycle Pokka plastic bottle and A&W plastic bottle was used to form the shape. I added two inset on each side of the mantle for the turbine placement. These were also make with recycled plastic wine glass :D This picture shows how the inset was "traced" out using embossing tape and the panel line scriber. Thank goodness for the scriber, as the plastic wine glass was very brittle... using the scriber to slowly engrave the plastic till it can be broken off in the intended direction really make it easy...and without saw dust all over the place is another plus point.
Once that's done, the turbines are next... Make with plastic spoons and the BZ-017 Laser storm's gatling body. Posing with the rest of the mantle :)
At this stage, I m tailing behind the competition~ Literally... Tail option 1 Tail option 2
After deciding on the tail option, i noticed that the putty popped away at the mantle from the plastic.. as the plastic underneath is way softer than the harden putty... So when implementing tail option 2, i thought up this idea :D 1)Roll the kneaded putty around a rod of blue-tac 2)Insert a stick into the center then rotate and spread the putty around the underside of the hole. 3) Finally gently pull the blue-tac up to make the "spreaded" blue tac press against the wall. 4) Simply pull out the blue-tac when the putty is dried. Voila, well-supported column for the tail section :D Finally, to join the mantle and the rest of the head together and covered up with another deathsaurer part ;) The rectangular part on the right is used as the funnel.
The inspiration for this custom came when I was creating 无(Wu). During the http://www.blogger.com/img/blank.gifcohttp://www.blogger.com/img/blank.gifckpit design phase, I found a cool design from the Gundam series... And the other inspiration came from the matrix's sentinel. Being a Zoids fan, the end result must be an organoid... so this is ithttp://www.blogger.com/img/blank.gif Yes, its a Squid :D But not just any squid, I want it to be the Humboldt squid (Red Devil Squid) as a deep sea vessel.
And to add to the challenge, I wanted to go green and use recycled plastic for this custom ;)
Category: Sci-Fi, Mecha, Zoids Scale: 1/24 Modification: Kit-bash from Deathsaurer and recycled plastic.
Type: Squid Class: Deep Sea Recon
Synopsis Inspired by the Humboldt squid (Red Devil Squid) thus named Akuma Red, this is a 1/24 representation of the one man vessel for deep sea recon.
The cockpit is fully rotatable 360degree so that the Akuma Red can lay in any 3D position without giving the controller invertigo sickness. With the latest digital camouflage technology and its naturally red color the Akuma Red is almost invisible. (In deep water, red is first color to lose its shade)
Now comes the real deal. I was able to confirm the outlook using the relatively inexpensive colored regular issue part. Now I have to work on the transparent counterpart...
Only after I make a closer inspection of the part did I release something unexpected in a normal build...
The mold lines on the internal side.... they are visible as the whole piece is see thru...And they are in hard-to-reach corners....I sand them down initially but in the end I just use my micro chisel to scratch them off...Next headache....after I cut off the unwanted part, white stress marks appeared due to the tension.... Again, sand and scratch with chisel...or finger nail~ Another approach is to cut them with a little buffer so that it can be removed with a less tension tool like a chisel or penknife. As the part selection is so limited, every single bit counts... I decide to get this photo etch saw to make the collateral damage to a minimum. And lastly, being transparent means that regular putty cant be used to seal up gap/holes... I brought a pack of clear putty but upon hearing poor review abt it, I decided not to risk it... So in the end I used clear silicon which is much cheaper... Beware tho, try not to handle them using your bare hand. Wear a latex glove or something. If any of those sticky thingy get onto you, try acetone (regular nail polish remover) Next are the tentacles... After I line up the glass beads, I still find them too blocky and it doesnt match the fluid idea that I have. So I decided to use clear heat shrink tubing to encase them so that they look like a single piece. Now come my blunder... in order to effectively shrink them, my hot hair blower cant really do it without short-circuiting the whole neighborhood power grid. So I used hot water...And it works nicely... but the side effect was if water happen to seep in.... the cheapo $2 wire will rust... no wonder I saw those expensive wire in the bead shop... those must be rust-resistant...
And finally, the paint job.... so... how do you color something that's supposed to be transparent... Well, you dont... hmmm, then again, you can :D
Try to have at least half of the part submerge into the solution. Keep the movement to a minimum to avoid stirring up too much bubbles... Rotate it around for the future to flood out the trapped bubbles. See the different? Not only it make it bling like glass, it helps to fill up little scratches. Hehee, so technically I did paint my custom and the color scheme is just that. Transparent. But its really a dust magnet... so keep it dust free... The new packaging is now called the Pledge with Future shine. This set me back $22SGD... but being a cheapo, I pour back whatever I used.... and now i notice there are now some particle inside the bottle...
And this is it.... Relatively lesser effort than my previous custom but was able to achieve the effect that I wanted :) If I can turn back time and redo this, I will add less tentacle and keep within the silhouette. I find the tentacle positioned too far in-front thus making the main body look short and lost the appearance of a buoyancy ballast compartment look. Overall it was great fun and the end result was worth the cost :)
In the end I spent another $30 buck to get a LED stripe that can change 7 colors to make my display look like those jellyfish tube in the aquarium :D
Once I'm happy with the placement, the fusion starts...
First I have to make the red horn feet merge with the body. This is done by slicing off the exhaust vent and leveling of the surrounding area by filing. Now they flow with the bodyline nicely:) But the hole for the original fore leg still remain... I tried using a transparent spoon to make the circular cover... The result didnt turn out as what I expected because the spoon is not in a perfect dome... it is slightly elongated and the final outlook seems like an eyelid...so it was aborted...
After I stick the feet onto the body, I found that the feet joint is prefect for making a turrent mounting :D Weeee
With the turret built using the existing guns from red horn, I realised that there is a break in the bodyline from the top view. Right infront of the first feet...
So again, I tried to find a solution from the leftover parts and managed to come up with this: Each cannon will be place right onto of the gap in the bodyline to create a continuous impression.
Synopsis Modeled after the infamous Portuguese Man-of-War (aka Blue bottle, Medusa), this Zoids is a huge carrier class Zoids capable of transport small to medium sized Zoids across the battlefield. With it 99% HoloTech (HT)capability, there is almost nothing to be seen, thus its been named 无(Wu) or nothingness. This carrier class Zoids is truly one of its kind. Its large landing craft body is not only able to float in the air and water depending on the molecule mixture loaded into its ballast, it can also be totally submerged into water. Look at those firepower mounted all around itself....Try to see if you can... Because not even the most sophisticated sensor system can pick up them... New advancements in energy R&D were implemented into the power module to enable the full time employment of the HT ability. Making it almost impossible to be detected by even its own army...if not for the mechanical cap at the base of its side mounted turrets and its tail. Shown here is the opened bay door during Zoids deployment. This is the only time the HT will be partially disabled. Cannot find where it is? Lets zoom in a little...
Just gotta recreate an aquarium experience that inspired me here...
Finally adding the darkest color and peel off all the tapes... O_o)"
